CONCRETE
OUR PRODUCTS
Compresion Testing Frames

EN 12390-4 and EN 772-1 Compression Testing Frames with Welded Walls for Cubes, Cylinders and Masonary Units

Product Code

UTC-5729

2000 kN EN 12390-4 and EN 772-1 Compression Testing Frames with Welded Walls for Cubes, Cylinders and Masonary Units

UTC-5739

3000 kN EN 12390-4 and EN 772-1 Compression Testing Frames with Welded Walls for Cubes, Cylinders and Masonary Units

UTC-4682E

Pedestal for  EN 1550 kN, 2000 kN, 2200 kN and 3000 kN Compression Testing Frames with Welded Walls

Standards
EN 12390-4, EN 12390-3, EN 772-1

Technical sheet Ask for Quote

UTC-5729 and UTC-5739 compression testing frames with rigid welded steel walls for masonary unıts, cubes and cylınders consist of a loading cylinder assembly, lower and upper (spherically-seated) loading platens. acc. to EN standards.

The frames are tested and certified for force transfer stability and the self-alignment of the upper loading platen conforming to EN 12390-4 by Utest.

EN compression testing frames provides the stability needed for accurate and repeatable test results over the years of operation.

The frames are supplied with factory calibration certificate for force transfer stability and the self-alignment of the upper loading platen conforming to EN 12390-4.

Any hydraulic power pack with control and read out unit and a pressure transducer for measuring the loads, can be  positioned on the right hand side of the load frame for easier accessibility, increased productivity and for safer operations.

All frames have a single acting up stroking ram and also have front and rear protective doors and limit swich for piston stroke for safety. The diameter of the pistona are designed to work with the load capacity. There is a low friction coaxial PTFE seal between the cylinder and the piston fitted to the cylinder.

The lower loading platens are provided with concentric centering lines and fixture for centering specimens

UTC-4682E Pedestal that is made of steel to facilitate  the user’s  placement of specimens in the frames for compression test should be ordered separately.

See the below table for supplied items with the frames.

EN 12390-4 and EN 772-1 COMPRESSION TESTING FRAMES

WITH WELDED WALLS FOR CONCTERE CUBES AND CYLINDERS AND MASONARY UNITS

Models

UTC-5729

UTC-5739

Product Photo

Capacity

2000 kN

3000 kN

Frame Type

Welded Steel

Welded Steel

Lower Bearing Block, Dimensions (D)

310x510x50 mm 

310x510x50 mm 

Upper Bearing Block, (With Spherically Seating Assembly ) Dimensions (C)

310x510x50 mm 

310x510x50 mm 

Surface Hardness of Bearing Blocks

 55 HRC

 55 HRC

Flatness Tolerance

0,03 mm

0,03 mm

Piston Diameter

250 mm

300 mm

Piston Stroke

50 mm

50 mm

Maximum Vertical Clearance

Between Bearing Blocks (E)

330 mm

330 mm

Horizontal Clearance (B)

360 mm

415 mm

Sizes of Specimens For Cylinders  (up to)

Ø160x320 mm

Ø160x320 mm

Sizes of Specimens For Cubes  (up to)

300 mm (**)

300 mm (**)

Sizes of Specimens For Masonary Units (up to)

300x500 mm (**)

300x500 mm (**)

Dimensions (wxlxh) (Axd*xF)

450x550x1145 mm

505x550x1205 mm

Weight

880 kg

1120 kg

Pedestal (Optional)

UTC-4682

UTC-4682

(d*) depth      

(**) Limited by capacity of the  frame

 

The machines  for masonary units, cubes and cylindrs are supplied complete with;

• 100 mm, 50 mm, 2x30 mm height x Ø205 mm  distance pieces.

• Fixture for Centering Specimens, compatible with 310x510x50 mm lower loading platen for 100 mm and 150 mm cubes, Ø100 mm and Ø150 mm cylinders.

• Scissor Jack for Loading Platens/Bearing Blocks (UTC-4629)

• Removable transparent front and rear safety doors

• The front safety doors have an automatic safety device to stop the machine if the door is opened during a test.

Appropriate Distance piece/s for the cylinder and cube specimens with the height of lower than 150 mm should be ordered separately.